Microwave Installation Cost in Irving, TX2026
Estimate microwave installation cost in Irving, TX by install type, electrical work, vent kit, cabinet modification, and haul-away.
Project Details
Total Estimated Cost
$259
Adjusted for local cost of living (-10%)
Cost Breakdown
Cost Distribution
Data sources: Base costs derived from national industry cost surveys and contractor pricing data, adjusted with BLS inflation indices, Census housing/income signals, and FRED CSV fallback when BLS data is temporarily unavailable. Regional adjustment (Irving, TX) based on U.S. Bureau of Labor Statistics Consumer Price Index data. Latest index refresh: April 2026.
Disclaimer: Estimates are approximate and for informational purposes only. Actual costs vary based on project complexity, contractor rates, material availability, and local market conditions. Always obtain multiple quotes from licensed contractors before starting a project.
Typical Project Cost by Install type
Adjusted for Irving, TX (-10%)Same default project size (default scope), priced across each material tier.
| Tier | Material rate | Total project | Installed per unit |
|---|---|---|---|
| Countertop / no install | $0 | $80 | $80 |
| Over-the-range replacement | — | $259 | $259 |
| OTR new install (no existing) | $348 | $393 | $393 |
| Built-in with trim kit | $448 | $483 | $483 |
| Drawer microwave | $547 | $572 | $572 |
Material rates reflect the latest BLS construction PPI adjustment. Installed totals include labor and supplies but exclude permits and any tear-out beyond the calculator's default scope.
Recent Cost Trends Affecting Irving
Wholesale construction prices typically lead homeowner-facing quotes by 2–4 months. Use the trend below to decide whether to pull a project forward or wait for the next reading.
Residential Construction PPI — Trailing 12 Months
BLS series PCU236211236211, single-family construction producer prices.
200.1
+0.9% vs Mar 25
The PPI is the wholesale price of materials and labor that contractors pay, before margin. A rising index usually flows into homeowner quotes within 2–4 months. Use this trend to decide whether to pull a project forward or wait.
Local Labor Rates Near Irving, TX
State-level mean hourly wages from BLS OEWS, May 2023.
| Trade | SOC | Mean hourly (TX) | vs national | Loaded billing rate |
|---|---|---|---|---|
| ElectriciansMost relevant | 47-2111 | $28.14 | -12.6% | ~$68/hr |
| HVAC MechanicsMost relevant | 49-9021 | $25.10 | -12.4% | ~$60/hr |
| Plumbers & Pipefitters | 47-2152 | $28.40 | -13.5% | ~$68/hr |
| Carpenters | 47-2031 | $22.43 | -22.5% | ~$54/hr |
| Painters | 47-2141 | $20.51 | -17.2% | ~$49/hr |
| Roofers | 47-2181 | $20.52 | -20.7% | ~$49/hr |
| Construction Laborers | 47-2061 | $18.95 | -16.8% | ~$45/hr |
"Mean hourly" is the BLS OEWS state-level cross-industry mean wage paid to the worker. Loaded billing rate is a typical 2.4× multiple used in residential bids to cover overhead, insurance, taxes, vehicle, and contractor margin. Use it as a sanity check on a quoted hourly rate.
Best Months to Schedule Interior painting in Irving, TX
Derived from NOAA climate normals for TX: heating/cooling degree days, freeze months, and annual precipitation.
Why these months
Interior work is climate-independent for cure, but contractors discount in winter because most exterior trades slow down. Booking interior jobs Dec–Feb often nets 5–15% lower quotes.
Booking tip
Ask for a winter or January discount and confirm ventilation if low-VOC paint is required.
Microwave Installation Cost by City
Browse all 202 cities by state
Alaska
Arkansas
California
Connecticut
Delaware
District of Columbia
Florida
Hawaii
Idaho
Illinois
Indiana
Kansas
Kentucky
Maine
Maryland
Minnesota
Mississippi
New Hampshire
New Jersey
New Mexico
North Carolina
North Dakota
Oklahoma
Pennsylvania
Rhode Island
South Carolina
South Dakota
Texas
Vermont
West Virginia
Wyoming
Local Market Context for Irving, TX
This Irving page currently uses modeled local pricing based on south regional CPI, state-level Census signals, metro premium assumptions, and the same project formulas used across the rest of the site.
Relative cost level
10% below national
This reflects the city multiplier currently applied to labor-sensitive project costs.
Local data source
Modeled regional CPI
This city currently uses regional CPI, state housing data, and metro premium modeling.
Market profile
South · 257K city population
Region and city size help explain labor pressure, contractor demand, and housing-stock mix.
Compare Nearby Markets
Check the same calculator in nearby or same-region cities to see how the local multiplier changes the estimate.
Microwave Installation cost in Lubbock
Texas market · smaller metro · 78 cost index · ~12% lower than Irving
Compare Microwave Installation pricing in Laredo, TX
Texas market · smaller metro · 80 cost index · ~10% lower than Irving
Garland microwave installation estimates
Texas market · smaller metro · 90 cost index · similar local pricing
How much microwave installation costs in Plano
Texas market · smaller metro · 94 cost index · ~4% higher than Irving
Microwave Installation prices around Frisco
Texas market · smaller metro · 93 cost index · ~3% higher than Irving
Amarillo, TX microwave installation budget
Texas market · smaller metro · 79 cost index · ~11% lower than Irving
Local microwave installation estimate for Grand Prairie
Texas market · smaller metro · 88 cost index · ~2% lower than Irving
Microwave Installation near Corpus Christi
Texas market · smaller metro · 80 cost index · ~10% lower than Irving
Average Cost in Irving, TX
For a typical microwave installation scenario in Irving, TX, this calculator currently models a total around $259, or about $259 per unit.
When budgeting Microwave Installation in Irving, local quotes usually reflect conditions across Texas. Code enforcement, permit processes, and labor pools vary widely between Texas metros, so the same scope can price differently from city to city.
Irving pricing still tracks South labor signals, even when the local contractor pool is smaller.
Home improvement quotes near Irving, TX are most sensitive to scope clarity, access, and which finishes are included versus "allowance only."
Local conditions in Irving, TX include long, hot summers and short, mild winters with strong storm exposure, which often shows up in material choices and scheduling.
Local building patterns in Irving mostly come from newer single-family with slab foundations and storm-rated roofing, which influences how crews price prep, demolition, and finish coordination.
In Irving, modeled costs are currently about 10% below the national baseline. That usually reflects a mix of smaller metro labor pricing, subcontractor availability, and broader south regional cost pressure.
Local labor conditions, permit timing, and finish selection all influence how this project prices in Irving.
Low / Mid / High Project Scenarios
Low Scenario
$260$260 per square foot
OTR replacement using existing electrical, recirculating filter.
Mid Scenario
$785$785 per square foot
OTR new install with overhead outlet, reuse existing duct, trim adjustment, curb pickup.
High Scenario
$1,645$1,645 per square foot
Drawer microwave install with new dedicated circuit, ducted wall vent, custom cabinet cutout.
What Changes the Estimate Most in Irving?
- Drawer and built-in trim-kit microwaves cost 2–3× more in labor than a standard OTR replacement.
- Ducted-vent retrofits through an exterior wall are the biggest cost jump over a recirculating filter install.
- New dedicated 20A circuits add cost but are recommended when sharing with high-draw kitchen circuits.
When This Calculator Is Less Accurate
This calculator is less accurate when the install includes custom drawer-microwave cabinetry, speed-oven combo units, integrated microwave/oven towers, or coordination with high-CFM range-hood and make-up-air systems.
Use the result as a budgeting starting point, then validate with local contractor quotes if the scope includes specialty materials, hidden damage, or permit-driven design changes.
How Much Does Microwave Installation Cost in Irving?
Microwave installation typically costs $100–400 for an over-the-range replacement, with built-in trim-kit and drawer microwaves landing $450–900+ once cabinet modification and electrical work are included. The biggest variables are whether the install is a like-for-like swap, a new ducted vent run, or a custom-fit cabinet cutout.
Cost Factors:
- Install type — countertop is free; OTR replace is the most common; drawer and built-in trim kits cost the most
- Electrical work — most microwaves want a dedicated 20A circuit, especially OTR units that share a circuit with the range
- Vent configuration — recirculating is cheapest; ducted-through-wall vents cost the most but move much more air
- Cabinet modification — trim kits and custom cutouts add $150–400+ in cabinetry and finishing labor
- Haul-away — old microwaves typically have curb pickup or low recycler disposal fees
In Irving, home improvement costs are 10% below the national average. This reflects local labor rates, material availability, and cost of living in the Irving metro area.
Frequently Asked Questions (5)
How localized is the Microwave Installation estimate for Irving, TX?
This page applies a South regional cost model plus local signals for Irving, TX, so totals are modeled around 10% below a national baseline before you change inputs. Use it as a budgeting range, then compare written quotes for your exact scope.
What should I verify with contractors in Irving?
Confirm permits, HOA or historic-district rules, material lead times, and whether demolition or hidden damage is included. Texas codes and local inspection steps can change both price and schedule compared with national averages.
How much does it cost to install an over-the-range microwave?
Like-for-like OTR replacements typically cost $150–300. New OTR installs (no existing microwave) run $350–500 because the installer has to mount the bracket, fish power, and add cabinet support. Adding a new ducted vent through an exterior wall pushes total cost to $600–900.
Do I need a vent hood if I have an over-the-range microwave?
Most building codes accept an OTR microwave as the vent hood for residential ranges. Recirculating mode is acceptable but ducted is much more effective, especially over gas ranges. Some HOAs and condo associations have additional venting requirements.
Can I install a built-in microwave myself?
Built-in microwaves with trim kits require precise cabinet sizing and proper ventilation clearances, so most homeowners hire a pro. Drawer microwaves are heavy (~80 lbs) and require a cabinet rated for the load — almost always a professional install.
Data sources & methodology
Estimates blend national base costs, the BLS residential construction PPI, regional and direct metro CPI series, BLS OEWS state labor wages, and U.S. Census ACS housing signals. Market data refreshed April 2026. Expect ±15–30% spread vs an actual contractor quote.
Explore Related Project Costs
These are common next-step comparisons for people researching microwave installation in Irving.
Microwave-hood vs dedicated range hood
Range Hood Installation Cost Calculator
Compare an OTR microwave with a dedicated ducted range hood for performance and cost.
Microwave plus new range
Oven & Range Installation Cost Calculator
Useful when replacing both primary and secondary cooking appliances together.
Microwave install plus cabinet work
Cabinet Installation Cost Calculator
Helpful when a new microwave triggers cabinet modifications or trim work.
Related Calculators
Range Hood Installation Cost Calculator
Estimate range hood install cost by hood type, venting, electrical work, cabinet changes, and labor.
Oven & Range Installation Cost Calculator
Estimate oven & range install cost by appliance type, gas/electric, and add-ons.
Cabinet Installation Cost Calculator
Estimate new cabinet install cost by linear footage, cabinet tier, demolition, finish carpentry, and labor.