Well Pump Cost in Irving, TX2026
Estimate well pump replacement cost in Irving, TX by pump type, well depth, pressure tank, electrical work, and removal. Typical range about $800-6,000.
Project Details
Total Estimated Cost
$583
Adjusted for local cost of living (-8%)
Cost Breakdown
Cost Distribution
Data sources: Base costs derived from national industry cost surveys and contractor pricing data, adjusted with BLS inflation indices, Census housing/income signals, and FRED CSV fallback when BLS data is temporarily unavailable. Regional adjustment (Irving, TX) based on U.S. Bureau of Labor Statistics Consumer Price Index data. Latest index refresh: June 2026.
Disclaimer: Estimates are approximate and for informational purposes only. Actual costs vary based on project complexity, contractor rates, material availability, and local market conditions. Always obtain multiple quotes from licensed contractors before starting a project.
Typical Project Cost by Pump Type
Adjusted for Irving, TX (-8%)Same default project size (default scope), priced across each material tier.
| Tier | Material rate | Total project | Installed per unit |
|---|---|---|---|
| Shallow Jet Pump — <25 ft | $399 | $583 | $0 |
| Deep Jet Pump — 25-100 ft | $698 | $1,019 | $0 |
| Submersible — 100-200 ft | $997 | $1,456 | $0 |
| Submersible — 200-400 ft | $1,496 | $2,184 | $0 |
| Submersible — 400 ft+ | $2,193 | $3,202 | $0 |
Material rates reflect the latest BLS construction PPI adjustment. Installed totals include labor and supplies but exclude permits and any tear-out beyond the calculator's default scope.
Recent Cost Trends Affecting Irving
Wholesale construction prices typically lead homeowner-facing quotes by 2–4 months. Use the trend below to decide whether to pull a project forward or wait for the next reading.
Residential Construction PPI — Trailing 12 Months
BLS series PCU236211236211, single-family construction producer prices.
200.6
+4.0% vs May 25
The PPI is the wholesale price of materials and labor that contractors pay, before margin. A rising index usually flows into homeowner quotes within 2–4 months. Use this trend to decide whether to pull a project forward or wait.
Local Labor Rates Near Irving, TX
State-level mean hourly wages from BLS OEWS, May 2023.
| Trade | SOC | Mean hourly (TX) | vs national | Loaded billing rate |
|---|---|---|---|---|
| Plumbers & PipefittersMost relevant | 47-2152 | $28.40 | -13.5% | ~$68/hr |
| Electricians | 47-2111 | $28.14 | -12.6% | ~$68/hr |
| HVAC Mechanics | 49-9021 | $25.10 | -12.4% | ~$60/hr |
| Carpenters | 47-2031 | $22.43 | -22.5% | ~$54/hr |
| Painters | 47-2141 | $20.51 | -17.2% | ~$49/hr |
| Roofers | 47-2181 | $20.52 | -20.7% | ~$49/hr |
| Construction Laborers | 47-2061 | $18.95 | -16.8% | ~$45/hr |
"Mean hourly" is the BLS OEWS state-level cross-industry mean wage paid to the worker. Loaded billing rate is a typical 2.4× multiple used in residential bids to cover overhead, insurance, taxes, vehicle, and contractor margin. Use it as a sanity check on a quoted hourly rate.
Best Months to Schedule Interior painting in Irving, TX
Derived from NOAA climate normals for TX: heating/cooling degree days, freeze months, and annual precipitation.
Why these months
Interior work is climate-independent for cure, but contractors discount in winter because most exterior trades slow down. Booking interior jobs Dec–Feb often nets 5–15% lower quotes.
Booking tip
Ask for a winter or January discount and confirm ventilation if low-VOC paint is required.
Well Pump Cost by City
Browse all 202 cities by state
Alaska
Arkansas
California
Connecticut
Delaware
District of Columbia
Florida
Hawaii
Idaho
Illinois
Indiana
Kansas
Kentucky
Maine
Maryland
Minnesota
Mississippi
New Hampshire
New Jersey
New Mexico
North Carolina
North Dakota
Oklahoma
Pennsylvania
Rhode Island
South Carolina
South Dakota
Texas
Vermont
West Virginia
Wyoming
Local Market Context for Irving, TX
This Irving page currently uses modeled local pricing based on south regional CPI, state-level Census signals, metro premium assumptions, and the same project formulas used across the rest of the site.
Relative cost level
8% below national
This reflects the city multiplier currently applied to labor-sensitive project costs.
Local data source
Modeled regional CPI
This city currently uses regional CPI, state housing data, and metro premium modeling.
Market profile
South · 257K city population
Region and city size help explain labor pressure, contractor demand, and housing-stock mix.
Compare Nearby Markets
Check the same calculator in nearby or same-region cities to see how the local multiplier changes the estimate.
Well Pump cost in Lubbock
Texas market · smaller metro · 79 cost index · ~13% lower than Irving
Compare Well Pump pricing in Laredo, TX
Texas market · smaller metro · 81 cost index · ~11% lower than Irving
Garland well pump estimates
Texas market · smaller metro · 91 cost index · ~1% lower than Irving
How much well pump costs in Plano
Texas market · smaller metro · 96 cost index · ~4% higher than Irving
Well Pump prices around Frisco
Texas market · smaller metro · 95 cost index · ~3% higher than Irving
Amarillo, TX well pump budget
Texas market · smaller metro · 80 cost index · ~12% lower than Irving
Local well pump estimate for Grand Prairie
Texas market · smaller metro · 89 cost index · ~3% lower than Irving
Well Pump near Corpus Christi
Texas market · smaller metro · 81 cost index · ~11% lower than Irving
Average Cost in Irving, TX
For a typical well pump scenario in Irving, TX, this calculator currently models a total around $583.
When budgeting Well Pump in Irving, local quotes usually reflect conditions across Texas. Code enforcement, permit processes, and labor pools vary widely between Texas metros, so the same scope can price differently from city to city.
Smaller markets like Irving can see fewer specialty crews on short notice, so scheduling and travel minimums sometimes matter more than in major cities.
In Irving, water quality and local code expectations can influence fixture choices, venting, and permit details.
Local conditions in Irving, TX include long, hot summers and short, mild winters with strong storm exposure, which often shows up in material choices and scheduling.
Irving's newer housing profile (newer single-family with slab foundations and storm-rated roofing) usually means fewer surprises behind the walls than in older Northeast and Midwest stock.
In Irving, modeled costs are currently about 8% below the national baseline. That usually reflects a mix of smaller metro labor pricing, subcontractor availability, and broader south regional cost pressure.
Local labor conditions, permit timing, and finish selection all influence how this project prices in Irving.
Low / Mid / High Project Scenarios
Low Scenario
$584Shallow jet pump replacement reusing existing tank and electrical.
Mid Scenario
$2,152Medium-depth submersible replacement with new standard pressure tank.
High Scenario
$5,924Very deep submersible with large pressure tank, new circuit and control box, and pump pull.
What Changes the Estimate Most in Irving?
- Well depth and pump type drive the equipment and labor cost more than any other variable in a pump project.
- Casing condition, drop-pipe length, and electrical supply distance are the main reasons well-pump labor exceeds a simple swap.
- Pressure tanks, constant-pressure controllers, and water-treatment tie-ins are the extras that most often push a well-pump bid higher.
When This Calculator Is Less Accurate
This calculator is less accurate when the project includes well rehabilitation, casing replacement, water-treatment system integration, or extreme-depth submersible work beyond a standard pump replacement.
Use the result as a budgeting starting point, then validate with local contractor quotes if the scope includes specialty materials, hidden damage, or permit-driven design changes.
How Much Does Well Pump Cost in Irving?
Replacing a well pump and related components often runs about $800-6,000 depending on whether you need a shallow jet, deep jet, or submersible pump, how deep the well is, and whether the pressure tank and wiring must be upgraded.
Cost Factors:
- Deeper wells usually need higher-head submersibles and longer pulls, which increases both equipment and labor
- Pressure tanks fail separately from pumps; upsizing can smooth cycling but costs more up front
- Corroded wire, failed control boxes, or insufficient breaker space add electrical scope beyond swapping the pump
- Pulling a stuck or sand-locked old pump can exceed a simple extraction allowance
- Water quality issues (iron, sediment) may suggest additional treatment not included in a bare pump swap
In Irving, home improvement costs are 8% below the national average. This reflects local labor rates, material availability, and cost of living in the Irving metro area.
Frequently Asked Questions (5)
How localized is the Well Pump estimate for Irving, TX?
This page applies a South regional cost model plus local signals for Irving, TX, so totals are modeled around 8% below a national baseline before you change inputs. Use it as a budgeting range, then compare written quotes for your exact scope.
What should I verify with contractors in Irving?
Confirm permits, HOA or historic-district rules, material lead times, and whether demolition or hidden damage is included. Texas codes and local inspection steps can change both price and schedule compared with national averages.
How much does it cost to replace a well pump?
Many homeowners pay roughly $800-6,000 depending on pump type, well depth, tank replacement, and electrical work. Submersible swaps on deep wells trend higher than shallow jet systems.
How do I know if I need a new pressure tank too?
Short cycling, waterlogged bladders, or rust-through shells are common reasons to replace the tank with the pump. A contractor can test drawdown and pre-charge to confirm.
Is labor included in the calculator?
Labor is modeled as a fraction of the selected pump equipment cost scaled by depth and regional multiplier, separate from parts like tanks and electrical allowances. Use it as a planning ballpark, not a bid.
Data sources & methodology
Estimates blend national base costs, the BLS residential construction PPI, regional and direct metro CPI series, BLS OEWS state labor wages, and U.S. Census ACS housing signals. Market data refreshed June 2026. Expect ±15–30% spread vs an actual contractor quote.
Explore Related Project Costs
These are common next-step comparisons for people researching well pump in Irving.
Softener with a new well pump
Water Softener Installation Cost Calculator
Well water often requires softening, so pairing a softener install with a pump replacement is common.
Well and septic together
Septic Tank Cost Calculator
Useful when both the well and septic system are part of the same rural property setup.
Pipe work with well pump
Pipe Repair Cost Calculator
Helpful when supply-line repairs are needed between the well head and the pressure tank.
Related Calculators
Water Heater Installation Cost Calculator
Estimate water heater install cost by unit type, venting, plumbing scope, permits, and haul-away.
Water Softener Installation Cost Calculator
Estimate water softener install cost by system type, plumbing loop, drain, electrical, removal, and labor.
Pipe Repair Cost Calculator
Estimate pipe repair or repipe cost by repair type, access difficulty, fixtures, and permits.